Posted on August 21, 2014 by Martin Fisher -
A full range of flexible ducting available in PVC, Foil, Rubber, Steel and Aluminium.
Weldline liners are fully welded single skin liners, suitable for all gas and light oil installations.
Welded seam single skin lining made from 0.1mm 316 grade stainless steel.
Approved for condensing boilers.
Approved for positive pressure.
SIZES
125, 150, 175, 200, 250, 300, 350, 400, 450, 500mm
BSRIA tested to BSEN 1856-2
Good selection of sizes available
Both flexible and durable
Posted on August 21, 2014 by Martin Fisher -
The Wells-Vent ductwork range offers a fully comprehensive range of stock and manufactured items to meet all requirements and installations.
Wells-Vent offers more than just standard galvanised ductwork and accessories.
With Wells you get an enormous choice and potential which cannot be beaten.
Stock range to DW144 ductwork standards. Any special design/fabrication available to order.
Also with the value added product ranges such as Well-Safe (gasket sealed ductwork), Wells-Twin (pre-insulated ductwork), Wells Colorducts and Wells-Vent (flat-oval) giving your a wider range of choice here at Wells.
Considerable material cost savings Due to the reinforcing effect of the 4-ply lockseam.
Rapid availability due to high levels of stock.
A wide range of fitting available, along with bespoke items manufactured to requirements
Posted on July 9, 2014 by Martin Fisher -
The coefficients of friction are the ratio of the actual force transmitted to the pile along its length to the calculated forces acting on the outer face of the pile (usually as predicted from soil investigations, of down drag, heave or negative skin friction). Our spiral tubes can be provided with a twin skin outer casing to reduce friction coefficients. The friction coefficient for twin plastic skins will be 0.2. For cases where very low coefficients are required, an inert, long life lubricant can be provided to form a greased sleeve wherein the friction coefficient reduces to approximately 0.1. It should be noted that the friction casings have very high chemical resistance and are inert to most reactants. The casings can therfore be used to prohibit corrosion and damp penetration to the pile.
This “twin-wall” system uses an external HDPE sleeve casing to reduce the friction co-efficient to as low as 0.2 and 0.1. The result is a unique answer to resist short term hydrostatic pressures from fresh concrete in weak surrounding soil, and long term subsoil movement, especially clay heave and negative skin friction. Uplift forces can be reduced by between 50% and 75%.
Diameters up to 2.2m readily available.
Ultra low friction coefficients down to 0.1
Uplift forces reduced between 50% and 70%
Negative skin friction reduced by 80% to 90%
Significant savings on pile size and reinforcements
Very high chemical resistance to sleeve
Mild steel, galvanised steel and other coated variants available
Posted on July 8, 2014 by Martin Fisher -
Feed and vent pipes (typically 4″ and 6″ diameter) can be supplied for new or old systems together with a full range of ducting for parlour feed supply.
Corrugated galvanised steel bulk bins are available in any length and in diameters up to 2.2 metres.
Culverts and Drainage
Feed and vent pipes (typically 4″ and 6″ diameter) can be supplied for new or old systems together with a full range of ducting for parlour feed supply
Ductwork
Long-life Aluzinc and galvanised steel.
Weather protected and fire resistant.
Posted on July 8, 2014 by Martin Fisher -
Used for cooling hot spots or small grain piles.
Supplied in part perforated/part solid, these pipes are typically 4″ diameter and approximately 8 feet long (although variations are available).
Peforated and solid ducts
Long-life Aluzinc and galvanised steel
Weather protected and fire resistant
Posted on July 8, 2014 by Martin Fisher -
Here at Wells Spiral we have the capability both to design and manufacture all types of dust, fume, odour, ventilation and pollution control systems for industry throughout the UK.
We design to our clients bespoke requirements and needs, ensuring all designs complies with current health and safety, environmental and COSHH regulations covering all aspects of industry.
A wide range of stock and made to order products are available for applications such as extract and supply ventilation systems, dust extraction, bulk conveying and handling, chimneys and vents.
Considerable material cost savings due to the reinforcing effect of the 4-ply lockseam.
Roundness perfect tube roundness ensured.
Bespoke one off systems and products
Posted on July 8, 2014 by Martin Fisher -
Posted on July 8, 2014 by Martin Fisher -
Posted on July 8, 2014 by Martin Fisher -
Posted on July 4, 2014 by Martin Fisher -
Recent Comments